Arkansas ODS CDL General Knowledge Practice Test 3
Test 3 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Arkansas test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. What information does an inspection decal on a commercial vehicle carry?
Show answer
Answer B: The date of the inspection, where the inspection report is kept, and information identifying the vehicle
The decal shows when the inspection was done, the name and address of the entity that holds the inspection report, and which vehicle it belongs to, so an officer can confirm the inspection at a glance.
-
2. For an unblocked article longer than 10 feet, the minimum is two tiedowns plus how many more?
Show answer
Answer B: One more for every additional 10 feet of length or any part of 10 feet
Past the first 10 feet, one more tiedown is added for each additional 10 feet of length or any fraction of that distance.
-
3. During the walkaround you notice one tire on an axle is a radial and the tire next to it is bias-ply. What should you do?
Show answer
Answer B: Treat it as a defect, because radial and bias-ply tires must not be mixed on the same axle
Radial and bias-ply tires flex and grip differently, so mixing them on one axle makes the vehicle handle unpredictably and is not allowed.
-
4. What must be checked about the cargo doors and any tarpaulin before a trip?
Show answer
Answer B: That the doors are closed and latched and that any tarp is tied down securely
An unlatched door or a loose tarp can swing open or tear free at speed, spilling cargo or blocking the view of the traffic behind you.
-
5. What does it mean to overdrive your headlights at night?
Show answer
Answer D: Driving so fast that you cannot stop within the distance lit by your headlights
You must be able to stop inside the distance you can see; at night that distance is limited by the headlights, so speed must be lowered to match.
-
6. What maximum speed does Arkansas law set for a truck of one-and-one-half-ton capacity or more outside an urban district and off a controlled-access highway?
Show answer
Answer D: 50 miles per hour
Arkansas Code 27-51-201 limits trucks of one-and-one-half-ton capacity or more to 50 miles per hour in locations other than urban districts and controlled-access highways.
-
7. What is the first step of the standard seven-step vehicle inspection?
Show answer
Answer C: A general overview of the vehicle, including the last inspection report
The routine opens with a walk-up overview of the vehicle and a review of the previous inspection report so known defects are addressed first.
-
8. You are hauling an open box of loose gravel. What does that load require?
Show answer
Answer A: A cover, so that material cannot blow off or spill onto the road
Loose material that can be blown or spilled has to be covered so it does not come out of the body and strike traffic behind.
-
9. Where is the yellow antilock brake malfunction lamp on a trailer, and what does it mean if it stays lit?
Show answer
Answer D: On the left side, at the front or rear corner, and it means the antilock function may not be working
Trailers carry the yellow lamp on the left side, and a lamp that stays on after the bulb check means the antilock function may be lost even though the normal brakes still work.
-
10. An intermodal container is being carried on an ordinary flatbed rather than on a container chassis. What does that mean for securement?
Show answer
Answer B: It must be secured with tiedowns that meet the container securement requirements
A container carried on a vehicle that is not fitted with integral locking devices has to be secured to the deck with tiedowns that satisfy the rules for containers.
-
11. Why can an empty truck need a longer stopping distance than a loaded one?
Show answer
Answer C: An empty vehicle has less traction, so its wheels lock up more easily
Brakes and tires are designed for a loaded vehicle, and with little weight on the axles the tires grip less and lock sooner.
-
12. For a modern truck with low-friction parts and a streamlined shape, which gear should be used going down a grade?
Show answer
Answer D: A gear lower than the one needed to climb the same grade
Newer trucks roll more freely than older ones, so the old rule of using the climbing gear no longer holds; a lower gear is needed for enough engine braking.
-
13. On the Interstate System, what is the federal maximum weight allowed on a single axle?
Show answer
Answer A: 20,000 pounds
Federal limits for the Interstate System cap one single axle at 20,000 pounds.
-
14. Where on a tire is tread depth measured?
Show answer
Answer C: In a major tread groove, away from any tie bar or wear indicator
Depth is taken in a major groove and away from the raised tie bars and wear indicators, which would give a shallower and misleading reading.
-
15. A commercial driver is convicted of two serious traffic violations within three years. What is the result?
Show answer
Answer D: Disqualification for 60 days
Two serious traffic violations in a three year period bring a 60 day disqualification, and a third in the same period raises it to 120 days.
-
16. After two hours of driving you measure a tire and the pressure reads higher than the cold figure. What should you do?
Show answer
Answer B: Nothing, because pressure rises normally as a tire heats up in use
Air expands as the tire heats, so a higher hot reading is expected, and letting air out leaves the tire underinflated once it cools.
-
17. What are you checking when you pull the engine oil dipstick during the pre-trip?
Show answer
Answer A: That the oil level is within the safe operating range marked on the stick
The dipstick shows whether there is enough oil to lubricate and cool the engine, and a level outside the safe range must be corrected before driving.
-
18. What does the driver check in the final step of the seven-step inspection?
Show answer
Answer A: Hydraulic brake leaks where those brakes are fitted, then the parking brake and the service brakes
The last step is done with the engine started: test for hydraulic leaks on vehicles with hydraulic brakes, then prove that the parking brake holds and that the service brakes stop the vehicle.
-
19. How often must every commercial motor vehicle receive a periodic inspection?
Show answer
Answer C: At least once every twelve months
Federal rules require each commercial motor vehicle to pass a periodic inspection at least once in every twelve month period.
-
20. At the end of the day you find no defects on a property carrying vehicle. What does the federal rule require?
Show answer
Answer B: No written report is required, although the carrier may still ask for one
For property carrying vehicles the report is required only when a defect or deficiency is found or reported, although a carrier may impose a stricter policy.
-
21. Why does a load of hanging meat in a refrigerated trailer require special care in curves?
Show answer
Answer D: The meat swings and has a high center of gravity, which makes the trailer unstable
Hanging meat is heavy, sits high and swings, so the trailer can tip in a curve or on a ramp taken at normal speed.
-
22. Which endorsements may be added to an Arkansas Commercial Learner's Permit?
Show answer
Answer A: Passenger, school bus and tank vehicle only
The Arkansas commercial manual states that only the passenger, school bus and tank vehicle endorsements may be added to a Commercial Learner's Permit.
-
23. You are pulling a loaded pneumatic dry bulk trailer and approach an exit ramp posted at 35 mph. What is the safest approach?
Show answer
Answer C: Slow to well below the posted speed before the ramp begins
A dry bulk trailer carries its weight high and the load can move, so the ramp speed posted for a car is far too fast and the slowing must be finished before the curve.
-
24. How can a driver tell that a shipment includes hazardous materials?
Show answer
Answer B: The shipping paper describes them and the packages carry hazard warning labels
Hazardous materials are identified on the shipping paper with their shipping name and hazard class, and the packages themselves carry labels showing the hazard.
-
25. Who may remove an out-of-service sticker from a commercial vehicle?
Show answer
Answer B: Only an authorized person, and only after the defect that caused it has been repaired
The sticker stays on the vehicle until the repairs are made and an authorized person removes it, so nobody can simply peel it off and drive away.
-
26. You are told a posted bridge ahead has a weight limit lower than your gross weight. What must you do?
Show answer
Answer C: Take a route that avoids it, because a posted limit is a legal limit
A posted structure limit must be obeyed exactly as any other weight limit, so a heavier vehicle has to be routed around it.
-
27. What is the payload of a truck?
Show answer
Answer C: The weight of the cargo the vehicle is carrying, that is the loaded weight less the empty weight
Payload is what is left of the legal or rated weight once the weight of the empty vehicle is taken off, and it is the weight of cargo that can be carried.
-
28. You are drifting in the lane, yawning constantly and cannot remember the last few miles. What is the only reliable cure?
Show answer
Answer C: Stopping in a safe place and sleeping
Those are classic drowsiness warning signs, and nothing except sleep repays the sleep the body is missing.
-
29. The paperwork shows a weight, but the load looks heavier than you expected. What should you do?
Show answer
Answer C: Weigh the vehicle, since you are the one answerable for driving it overweight
The driver is the one who can be cited for an overweight vehicle, so a doubtful weight is settled on a scale before the trip continues.
-
30. You normally pull an empty trailer, but today the same tractor is loaded to its legal maximum. What changes about getting under way?
Show answer
Answer A: You may need to start in a lower gear, since the load takes more pulling power
The heavier the load, the lower the gear needed to get the vehicle rolling without lugging or stalling the engine.
-
31. What should be checked about the power steering system in the engine compartment?
Show answer
Answer D: That the fluid level is correct and the hoses and pump are not leaking
Losing power steering fluid means losing steering assistance, which can happen suddenly and makes a heavy vehicle very hard to turn.
-
32. Why is a quick lane change particularly risky with a load of hanging meat or of livestock?
Show answer
Answer A: The load swings or leans and can keep pushing the trailer after you straighten out
A swinging or leaning load keeps moving after the vehicle has finished the maneuver, so its momentum acts on the trailer at the worst moment.
-
33. Federal rules keep recapped and retreaded tires off the front wheels of which vehicle?
Show answer
Answer B: Any bus carrying passengers
The federal rule names buses: a bus may not run with regrooved, recapped or retreaded tires on its front wheels, because a steer tire failure with passengers aboard takes away steering control.
-
34. How can a driver restart the 60 or 70 hour on-duty limit?
Show answer
Answer B: Take 34 or more consecutive hours off duty
A period of 34 or more consecutive hours off duty resets the 60 or 70 hour calculation so the driver can begin a new period.
-
35. In the seven-step method, what comes immediately after starting the engine and inspecting inside the cab?
Show answer
Answer D: Turn off the engine and check the lights
Step four shuts the engine down and switches on the lamps needed for driving so the driver can leave the cab and confirm they actually work.
-
36. Federal rules require a power unit that is not carrying placarded hazardous materials to have a fire extinguisher with which minimum rating?
Show answer
Answer A: One rated 5 B:C or more, or two rated 4 B:C or more each
The minimum is a single unit rated 5 B:C or more, or two units of at least 4 B:C each, which is enough to attack a fuel or electrical fire.
-
37. Why is it harder to judge speed and distance at night?
Show answer
Answer C: You see much less detail and have fewer reference points
Darkness removes the visual references that the brain uses to estimate distance and closing speed, so drivers routinely misjudge both.
-
38. How is free play in the steering wheel measured during the inspection?
Show answer
Answer B: By turning the wheel until the front wheels just start to move and noting the movement
Play is the movement at the rim that produces no movement at the road wheels, so it is measured by turning until the wheels first respond.
-
39. You are entering a freeway from a short ramp with a fully loaded trailer. What should you do?
Show answer
Answer A: Begin building speed early and wait for a large gap
A loaded vehicle accelerates slowly, so it needs both a running start and a much larger gap than a car would use.
-
40. Your brakes have failed and you decide to use the parking brake to slow down. Why should you hold the release button or lever while doing so?
Show answer
Answer D: So you can release the brake at once if the wheels lock and the vehicle starts to skid
The parking brake can lock the wheels; keeping your hand on the release lets you let go the moment a skid starts and regain control.
-
41. What frame defects are you looking for during the walkaround?
Show answer
Answer A: Cracks, bends or broken cross members
The frame carries the whole load, so cracked or bent rails and broken cross members are serious structural defects.
-
42. How should speed and gears be handled when approaching a curve?
Show answer
Answer A: Slow to a safe speed and downshift before entering the curve
Braking and shifting are completed before the curve so the vehicle is settled and can pull gently through it without upsetting the load.
-
43. How much free play in the steering wheel is enough to make a vehicle hard to steer and should be reported?
Show answer
Answer B: More than 10 degrees, roughly 2 inches of movement at the rim of a 20 inch wheel
Excess play means steering input is lost before the wheels respond, and more than about 10 degrees is treated as a defect.
-
44. What does the federal bridge formula do?
Show answer
Answer C: It reduces the weight allowed on a group of axles as those axles get closer together
Axles bunched together concentrate the load on a short span of a bridge, so the formula lowers the allowable weight as the spacing shrinks.
-
45. The engine oil pressure gauge falls toward zero while you are driving. What should you do?
Show answer
Answer C: Stop as soon as it is safe to do so and shut the engine down
Loss of oil pressure destroys an engine in a very short time, so the correct response is to stop and shut down rather than to drive on.
-
46. Which vehicle is most likely to be pushed around by a strong crosswind?
Show answer
Answer B: An empty van trailer
A large flat side with very little weight behind it gives the wind the most surface and the least resistance, which is the empty van trailer.
-
47. On a two lane road carrying traffic in both directions, where do the three warning devices go?
Show answer
Answer C: About 10 feet from the vehicle on the traffic side, 100 feet behind and 100 feet ahead
Traffic can approach from either direction, so one device goes close to the vehicle and one is placed about 100 feet away in each direction.
-
48. You have backed into the same loading bay every week for a year. How often should you still get out and walk to the rear before backing?
Show answer
Answer D: Every time, since the area can change while you are away from it
A familiar space is no guarantee; vehicles, pallets, people and overhead obstructions appear between one visit and the next, so you check on every occasion.
-
49. Which items belong to the in-cab part of the inspection?
Show answer
Answer D: Gauges, controls, mirrors, windshield, wipers, horn, heater and defroster
The in-cab step checks the instruments and controls the driver depends on, along with mirrors, glass, wipers, horn and the heater and defroster.
-
50. At a rest area you find that the load has shifted although the straps still feel tight. What should you do?
Show answer
Answer C: Correct the load before driving on, since a shifted load is no longer secure
Movement means the securement has already failed once, and a load that has shifted can shift again, so it is put right before the vehicle moves.